Industrial Biotechnology - Islamic University of Gaza

Industrial Biotechnology - Islamic University of Gaza

Industrial Biotechnology Lecturer Dr. Kamal E. M. Elkahlout Assistant Prof. of Biotechnology 1 CHAPTER 6 Overproduction of Metabolites of Industrial Microorganisms 2

The organisms genetic apparatus determines in the overall synthetic potentialities. What is actually synthesized depends on what is available in the environment. The organism is able to decide when to manufacture and secrete certain enzymes to enable it to utilize materials in the environment. It is able to decide to stop the synthesis of certain compounds if they are supplied to it. These sensing mechanisms for the switching on and off enable the organism to avoid the overproduction of any particular compound.

If it did not have these regulatory mechanisms it would waste energy and resources . Such an organism while surviving well in nature would not, however, be of much use as an industrial organism. In industrial biotechnology the wasteful organism with poor regulatory mechanisms is prefered. It will overproduce the particular metabolite sought. Knowledge of the regulatory mechanisms and biosynthetic pathways is essential.

This will enable the industrial microbiologist to derange and disorganize them so that the organism will overproduce desired materials. Processes by which the organism regulates itself and avoids overproduction using enzyme regulation and permeability control will first be discussed. Then will follow a discussion of methods by which the microbiologist consciously deranges these two mechanisms to enable overproduction. Genetic manipulation of organisms will be discussed in the next chapter.

MECHANISMS ENABLING MICROORGANISMS TO AVOID OVERPRODUCTION OF PRIMARY METABOLIC PRODUCTS THROUGH ENZYME REGULATION Substrate Induction Some enzymes are produced only when their substrate is available in the medium. (inducible enzymes). Analogues of the substrate may act as the inducer. When an inducer is present in the medium a number of different inducible enzymes may sometimes be synthesized by the organism.

The pathway for the metabolism of the compound is based on sequential induction. In this situation the organism is induced to produce an enzyme by the presence of a substrate. The intermediate resulting from the action of this enzyme on the substrate induces the production of another enzyme and so on until metabolism is accomplished. Group of enzymes is produced whether or not the substrate on which they act, are present. These enzymes are known as constitutive. Enzyme induction enables the organism to respond rapidly,

sometimes within seconds, to the presence of a suitable substrate, so that unwanted enzymes are not manufactured. Molecular basis for enzyme induction: The molecular mechanism for the rapid response of an organism to the presence of an inducer in the medium relates to protein synthesis. Two models exist for explaining on a molecular basis the expression of genes in protein synthesis: one is a negative control and the other positive. The negative control of Jacob and Monod first published in 1961 is the better known and more widely accepted of the two and will be described first.

The Jacob-Monod Model of the (negative) control of protein synthesis Synthesis of enzymes protein is regulated by a group of genes known as the operon and which occupies a section of the chromosomal DNA. An operon includes a regulator gene (R) which codes for a repressor protein. The repressor can bind to the operator gene (O) which controls the activity of the neighboring structural genes (S). The production of the enzymes which catalyze the transcription of the message on the DNA into mRNA (namely, RNA polymerase) is controlled by the promoter gene (P). If the repressor protein is combined with the operator gene (O) then

the movement of RNA polymerase is blocked and RNA complementary to the DNA in the structural genes (S) cannot be made. Consequently no polypeptide and no enzyme will be made. In the absence of the attachment of the repressor to the operator gene, RNA polymerase from the promoter can move to, and transcribe the structural genes, S. Inducible enzymes are made when an inducer is added. Inducers inactivate or remove the repressor protein thus leaving the way clear for protein synthesis. Constitutive enzymes occur where the regulator

gene (R) does not function, produces an inactive repressor, or produces a repressor to which the operator cannot bind. Often more than one structural gene may be controlled by a given operator. Mutations can occur in the regulator (R) and operator (O) genes thus altering the nature of the repressor or making it impossible for an existing repressor to bind onto the operator. Such a mutation is called constitutive and it eliminates the need for an inducer.

The structural genes of inducible enzymes are usually repressed because of the attachment of the repressor to the operator. During induction the repressor is no longer a hindrance, hence induction is also known as de-repression. In the model of Jacob and Monod gene expression can only occur when the operator gene is free. (i.e., in the absence of the attachment of the repressor protein the operator gene O. For this reason the control is said to be negative. Positive control of protein synthesis Positive control of protein synthesis has been established in at

least one system, namely the ara operon, which is responsible for L-arabinose utilization in E. coli. In this system the product of one gene (ara C) is a protein which combines with the inducer arabinose to form an activator molecule which in turn initiates action at the operon. In the scheme as shown in Fig. 6.2, C protein combines with arabinose to produce an arabinose C protein complex which binds to the Promoter P and initiates the synthesis of the various enzymes isomerase, kinase, epimerase) which convert L-arabinose to D-xylulose-5-phosphate, a form in which it can be utilized in the Pentose Phosphate pathway. Positive control of protein synthesis also operates during

catabolite repression. Catabolite Regulation If two carbon sources are available to an organism, the organism will utilize the one which supports growth more rapidly, Enzymes needed for the utilization of the less available carbon source are repressed and therefore will not be synthesized. As this was first observed when glucose and lactose were supplied to E. coli, it is often called the glucose effect. Glucose is the more available of the two sugars and lactose utilization is suppressed as long as glucose is available. The effect was not directly a glucose effect but was due to some

catabolite. The term catabolite repression was therefore adopted as more appropriate. Other carbon sources can cause repression and that sometimes it is glucose which is repressed. (cAMP) was the active catabolite involved in such repression, (Fig. 6.3). In general, less c-AMP accumulates in the cell during growth on carbon compounds supporting rapid growth of the organism, vice versa.

During the rapid growth on glucose, the intracellular concentration of cyclic AMP is low. C-AMP stimulates the synthesis of a large number of enzymes and in necessary for the synthesis of the mRNA for all the inducible enzymes in E.coli. When it is low the enzymes which need to be induced for the utilization of the less available substrate are not synthesized. Unlike the negative control of Jacob and Monod, c-Amp exerts a positive control. Another model explains the specific action in catabolite repression of glucose. In this model an increased concentration of c-AMP is a signal for

energy starvation. c-Amp binds to an intracellular protein, c-AMP-receptor protein (CRP). The binds complex to the promoter site of an operon stimulates the initiation of operon transcription by RNA polymerase (Fig. 6.3). The presence of glucose or a derivative of glucose inhibits adenylate cyclase the enzyme which converts ATP to c-AMP. Transcription by susceptible operons is inhibited as a result. In short, therefore, catabolite repression is reversed by c-AMP. It has been shown that c-AMP and CRP are not the only mediators of catabolite repression.

It has been suggested that while catabolite repression in enterobacteria at least is exerted by the catabolite(s) of a rapidly utilized glucose source It is regulated in a two-fold manner: positive control by c-AMP and a negative control by a catabolite modulation factor (CMF) which can interfere with the operation of operons senstitive to catbolite repression. In Bacillus c-AMP has not been observed, but an analogue of c-AMP is probably involved. Feedback Regulation Feedback or end-product regulations control

exerted by the end-product of a metabolic pathway. Feedback regulations are important in the control over anabolic or biosynthetic enzymes Enzymes involved in catabolism are usually controlled by induction and catabolite regulation. Two main types of feedback regulation exist: feedback inhibition and feedback repression. Both of them help adjust the rate of the production of pathway end products (see Fig. 6.4). Feedback inhibition The final product of metabolic pathway inhibits the action of

earlier enzymes (usually the first) of that sequence. The inhibitor and the substrate need not resemble each other, hence the inhibition is often called allosteric. In case of isosteic inhibition the inhibitor and substrate have the same molecular conformation. Feedback inhibition can be explained on an enzymatic level by the structure of the enzyme molecule. Such enzymes have two type of protein sub-units. The binding site on the sub-unit binds to the substrate while the site on the other sub-unit binds to the feedback inhibitor. When the inhibitor binds to the enzyme the shape of the enzymes is changed and for this reason, it is no longer able to

bind on the substrate. The situation is known as the allosteric effect. Feedback Repression Feedback inhibition results in the reduction of the activity of an already synthesized enzyme. Feedback repression deals with a reduction in the rate of synthesis of the enzymes. The regulator gene (R) is said to produce a protein aporepressor which is inactive until it is attached to corepressor, which is the end-product of the biosynthetic pathway.

The activated repressor protein then interacts with the operator gene (O) and prevents transcription of the structural genes (S) on to mRNA. A derivative of the end-product may also bring about feedback repression. It is particularly active in stopping the over production of vitamins, which are required only in small amounts (see Fig. 6.1). Feedback inhibition acts rapidly, sometimes within seconds. Feedback repression acts more slowly both in its

introduction and in its removal. About two generations are required for the specific activity of the repressed enzymes to rise to its maximum level when the repressing metabolite is removed. The same number of generations are also required for the enzyme to be repressed when a competitive metabolite is introduced. Regulation in branched pathway Several patterns of feedback inhibition have been evolved for branched pathways of which only six

will be discussed. Fig. 6.4 (i) Concerted or multivalent feedback regulation: Individual end-products F and H have little or no negative effect, on the first enzyme, E1, but together they are potent inhibitors. It occurs in Salmonella in the branched sequence leading to valine, leucine, isoleucine and pantothenic acid. (ii) Cooperative feedback regulation: In this case the end-products F and H are individually weakly inhibiting to the primary enzyme, E1, but

together they act synergistically, exerting an inhibition exceeding the sum of their individual activities. (iii) Cumulative feedback regulation: In this system an end-product for example (H), inhibits the primary enzyme E1 to a degree which is not dependent on other inhibitors. A second inhibitor further increases the total inhibition but not synergistically. Complete inhibition occurs only when all the products (E, G, H in Fig. 6.4) are present. (iv) Compensatory antagonism of feedback

regulation: This system operates where one of the endproducts, F, is an intermediate in another pathway J, K, F (Fig. 6.4). In order to prevent the other end-product, H, of the original pathway from inhibiting the primary Enzyme E1, and thus ultimately causing the accumulation of H, the intermediate in the second pathway J, K is able to prevent its own accumulation by decreasing the inhibitory effect of H on the primary enzyme E1. (v) Sequential feedback regulation:

Here the end-products inhibit the enzymes at the beginning of the bifurcation of the pathways. This inhibition causes the accumulation of the intermediate just before the bifurcation. It is the accumulation of this intermediate which inhibits the primary enzyme of the pathway. (vi) Multiple enzymes (isoenzymes) with specific regulatory effectors: Multiple primary enzymes are produced each of which catabolizes the same reaction from A to B but is controlled by a different end-product. Thus if one end-product inhibits one primary enzyme, the

other end products can still be formed by the mediation of one of the remaining primary enzymes. Amino Acid Regulation of RNA Synthesis Cells avoids overproduction of unwanted RNA by stopping both proteins & RNA synthesis when an amino acid supplement is exhausted. Such economical strains are stringent. Some mutated strains are relaxed. They continue to produce RNA in the absence of the required amino acid. The stoppage of RNA synthesis in stringent strains is

due to the production of the nucleotide guanosine tetraphosphate (PpGpp) and guanosine pentaphosphate (ppGpp) when the supplied amino acid becomes limiting. The amount of ppGpp in the cell is inversely proportional to the amount of RNA and the rate of growth. Relaxed cells lack the enzymes necessary to produce ppGpp from guanosine diphosphate and ppGpp from guanosine triphosphate. Energy Charge Regulation The cell can also regulate production by the amount of

energy it makes available for any particular reaction. The cells high energy compounds, (ATP), (ADP), (AMP) are produced during catabolism. The amount of high energy in a cell is given by the adenylate charge or energy charge. This measures the extent to which ATP-ADP-AMP systems of the cell contains high energy phosphate bonds, and is given by the formula. The charge for a cell falls between 0 and 1.0 by a system resembling feedback regulation. At the branch point in carbohydrate metabolism PEP

is either dephosphorylated to give pyruvate or carboxylated to give oxalocetate. A high adenylate charge inhibits dephosphorylation and so leads to decreased synthesis of ATP. A high energy charge on the other hand does not affect carboylation to oxaloacetate. It may indeed increase it because of the greater availability of energy. Permeability Control Metabolic control prevents the overproduction of essential macromolecules.

Permeability control enables the microorganisms to retain these molecules within the cell & to selectively permit the entry of some molecules from the environment. This control is exerted at the cell membrane. Several means are available for the transportation of solutes through membranes: (a) passive diffusion, (b) active transport via carrier or transport mechanism. Passive transport The driving force for transportation is the concentration

gradient in the case of non-electrolytes or in the case of ions the difference in electrical charge across the membrane between the internal of the cell and the outside. Yeasts take up sugar by this method. Few compounds outside water pass across the border by passive transportation. Transportation via specific carriers Most solutes pass through the membrane via some specific carrier mechanism in which macro-molecules situated in the cell membrane act as ferryboats, picking up solute molecules and helping them across the membrane.

Three of such mechanisms are known: (i) Facilitated diffusion: This is the simplest of the three, and the driving force is the difference in concentration of the solute across the border. The carrier in the membrane merely helps increase the rate of passage through the membrane, and not the final concentration in the cell. (ii) Active transport: This occurs when material is accumulated in the cell against a concentration gradient. Energy is expended in the transportation through the aid of

enzymes known as permeases but the solute is not altered. The permeases act on specific compounds and are controlled in many cases by induction or repression so that waste is avoided. (iii) Group translocation: In this system the solute is modified chemically during the transport process, after which it accumulates in the cell. The carrier molecules act like enzymes catalyzing group-transfer reactions using the solute as substrate. Group translocation can be envisaged as consisting of

two separate activities: The entrance process and the exit process. The exit process increases in rate with the accumulation of cell solute and is carrier-mediated, but it is not certain whether the same carriers mediate entrance and efflux. Carrier-mediated transportation is selective, and is the rate-limiting step in the metabolism of available carbon and energy sources. Increasing rate of accumulation of metabolizable carbon source can increase the extent of catabolite

repression of enzyme synthesis. The rate of metabolizable carbon transport may have widespread effects on the metabolism of the entire organism. DERANGEMENT OR BYPASSING OF REGULATORY MECHANISMS FOR THE OVER-PRODUCTION OF PRIMARY METABOLITES The methods used for the derangement of the metabolic control of primary metabolites will be discussed under the following headings: (1) Metabolic control; (a) feedback regulation, (b) restriction of enzyme activity;

(2) Permeability control. Metabolic Control Feedback control Feedback control is the major means by which the overproduction of amino acids and nucleotides is avoided in microorganisms. The basic ingredients of this manipulation are knowledge of the pathway of synthesis of the metabolic product and the manipulation of the organism to produce the appropriate mutants. (i) Overproduction of an intermediate in an unbranched pathway: Consider the production of end-product E following

the series in Fig. 6.5. End-product E inhibits Enzyme 1 and represses Enzymes 2, 3, and 4. An auxotrophic mutant is produced lacking Enzyme 3. Such a mutant therefore requires E for growth. If limiting (low levels) of E are now supplied to the medium, the amount in the cell will not be enough to cause inhibition of Enzyme 1 or repression of Enzyme 2 and C will therefore be over produced, and excreted from the cells. This principle is applied in the production of ornithine

by a citrulline-less mutant (citrulline auxotroph) of Corynebacterium glutamicum to which low level of arginine are supplied (Fig. 6.6). (ii) Overproduction of an intermediate of a branched pathway; Inosine 5- monophosphate (IMP) fermentation: Nucleotides are important as flavoring agents and the overproduction of some can be carried out as shown in Fig. 6.7. In the pathway shown in Fig. 6.7 end-products adenosine 5- monophosphate (AMP) and guanosine

5- monophsophate (GMP) both cumulatively feedback inhibit and repress the primary enzyme [1]. Furthermore, AMP inhibits enzyme [11] which coverts IMP to xanthosine-5- monophosphate (XMP). By feeding low levels of adenine to an auxotrophic mutant of Corynebacterium glutamicum which lacks enzyme [11] (also known as adenineless because it cannot make adenine) IMP is caused to accumulate. The conversion of IMP to XMP is inhibited by GMP at [13]. When the enzyme [14] is removed by mutation, a

strain requiring both guanine and adenine is obtained. Such a strain will excrete high amounts of XMP when fed limiting concentrations of guanine and adenine. (iii) Overproduction of end-products of a branched pathway: The overproduction of end-products is more complicated than obtaining intermediates. Among end-products themselves the production of end-products of branched pathways is easier than

in unbranched pathways. This is best illustrated (Fig. 6.8) using lysine, an important amino acid lacking in cereals and therefore added as a supplement to cereal foods especially in animal foods. It is produced using either Corynebacterium glutamicum or Brevibacterium flavum. Lysine is produced in these bacteria by a branched pathway that also produces methionine, isoleucine, and threonine. The initial enzyme in this pathway aspartokinase is

regulated by concerted feedback inhibition of threonine and lysine. By mutational removal of the enzyme which converts aspartate semialdehyde to homoserine, namely homoserine dehydrogenase, the mutant cannot grow unless methionine and threonine are added to the medium. As long as the threonine is supplied in limiting quantities, the intracelluar concentration of the amino acid is low and does not feed back inhibit the primary enzyme, aspartokinase.

The metabolic intermediates are thus moved to the lysine branch and lysine accumulates in the medium Figure 6.8. (iv) Overproduction of end-product of an unbranched pathway: Two methods are used for the overproduction of the end-product of an unbranched pathway. The first is the use of a toxic analogue of the desired compound and the second is to back-mutate an auxotrophic mutant. Use of toxic or feedback resistant analogues:

The organism (yeast cells, or fungal spores) are first exposed to a mutagen. They are then plated in a medium containing the analogue of the desired compound, which is however also toxic to the organism. Most of the mutagenized cells will be killed by the analogue. Those which survive will be resistant to the analogue and some of them will be resistant to feedback repression and inhibition by the material whose overproduction is desired. This is because the mutagenized organism would have been fooled into surviving on a substrate similar to, but

not the same as offered after mutagenesis. As a result it may exhibit feedback inhibition in a medium containing the analogue but may be resistant to feed back inhibition from the material to be produced, due to slight changes in the configuration of the enzymes produced by the mutant. The net effect is to modify the enzyme produced by the mutant so that it is less sensitive to feedback inhibition. Alternatively the enzyme forming system may be so

altered that it is insensitive to feedback repression. Table 6.2 shows a list of compounds which have been used to produce analogue-resistant mutants. Use of reverse Mutation: A reverse mutation can be caused in the structural genes of an auxotrophic mutant in a process known as reversion. Enzymes which differ in structure from the original enzyme, but which are nevertheless still active, often result. It has been reported that the reversion of auxotrophic

mutants lacking the primary enzyme in a metabolic pathway often results in revertants which excrete the end-product of the pathway. The enzyme in the revertant is active but differs from the original enzyme in being insensitive to feedback inhibition. Restriction of enzyme activity In the tricarboxylic acid cycle the accumulation of citric acid can be encouraged in Aspergillus niger by limiting the supply to the organism of phosphate and the metals which form components of coenzymes.

These metals are iron, manganese, and zinc. In citric acid production the quantity of these is limited, while that of copper which inhibits the enzymes of the TCA cycle is increased.

Permeability Ease of permeability is important. It facilitates the isolation of the product . Removal of the product from the site of feedback regulation. Non-diffused out product required disruption of the cell to isolate it, , thereby increasing costs. E.g. in glutamic acid producing bacteria, the permeability must be altered in order that a high level of amino acid is

accumulated in the broth. Increasing of permeability can be induced by several methods: (i) Biotin deficiency: Biotin is a coenzyme in carboxylation and transcarboxylation reactions, including the fixation of CO2 to acetate to form malonate. The formation of malonyl COA by acetyl-COA carboxylase is the limiting factor in the synthesis of long chain fatty acids. Biotin deficiency would therefore cause aberrations in the fatty acid production and hence in the lipid

fraction of the cell membrane, resulting in leaks in the membrane. Biotin deficiency has been shown also to cause aberrant forms in Bacillus polymax, B. megaterium, and in yeasts. (ii) Use of fatty acid derivatives: Fatty acid derivatives which are surface-acting agents e.g. polyoxylene-sorbitan monostearate (tween 60) and tween 40 (-monopalmitate) have actions similar to biotin and must be added to the medium before or during the log phase of growth.

These additives seem to cause changes in the quantity and quality of the lipid components of the cell membrane. For example they cause a relative increase in saturated fatty acids as compared to unsaturated fatty acids. (iii) Penicillin: Penicillin inhibits cell-wall formation in susceptible bacteria by interfering with the crosslinking of acetylmuranmic-polypeptide units in the mucopeptide.

The cell wall is thus deranged causing glutamate excretion. REGULATION OF OVERPRODUCTION IN SECONDARY METABOLITES There is increasing evidence that controls similar to those discussed for primary metabolism also occur in secondary metabolites. Induction The stimulatory effect of some compounds in secondary metabolite fermentation resembles enzyme induction. E. g., role of tryptophan in ergot alkaloid fermentation

by Claviceps sp., The amino acid is a precursor. It induces some enzymes needed for the biosynthesis of the alkaloid. The effect was discovered as analogues of tryptophan induce the enzymes used for the biosynthesis of the alkaloid. Tryptophan must be added during the growth phase otherwise alkloid formation is severely reduced. This would also indicate that some of the biosynthetic enzymes, or some chemical reactions leading to alkaloid

transformation take place in the trophophase, thereby establishing a link between idiophase and the trophophase. A similar induction effect exerted by methionine in the synthesis of cephalosporin C by Cephalosporium ocremonium. Catabolite Regulation Catabolite regulation can be by repression or by inhibition. It is not known which of them is operating in secondary metabolism. Catabolite regulations not limited to carbon catabolites Nitrogen catabolite regulation noted in primary metabolism also occurs in secondary metabolism

Carbon catabolite regulation It is known for a long time. Penicillin is not produced in a glucose-containing medium until after the exhaustion of the glucose, when the idiophase sets in. Same effect was observed with cephalosporin production. Glucose effect is well known in a large number of secondary products. Other carbon sources may be preferred in two-sugar systems when glucose is absent. -carotene production by Mortierella sp. is best on

fructose even though galoctose is a better carbonsource for growth. Carbon sources which have been found suitable for secondary metabolite production include sucrose (tetracycline and erythromycin), soyabena oil (kasugamycin), glycerol (butirosin) and starch and dextrin (fortimicin). (Table 6.3). Synthesis of the enzymes necessary for the synthesis of the metabolite is repressed. It is tested by the addition of the test substrate just prior to the initiation of secondary metabolite synthesis.

To test for catabolite inhibition by glucose or other carbon source it is added to a culture already producing the secondary metabolite and any inhibition in the synthesis noted. Nitrogen catabolite regulation It has also been observed in primary metabolism. It involves the suppression of the synthesis of enzymes which act on nitrogen-containing substances (proteases, ureases, etc.) until the easily utilizable nitrogen sources e.g., ammonia are exhausted. In streptomycin fermentation where soyabean meal is the

preferred substrate as a nitrogen source the advantage may well be similar to that of lactose in penicillin, namely that of slow utilization. Secondary metabolites which are affected by nitrogen catabolite regulation include trihyroxytoluene production by Aspergillus fumigatus, bikaverin by Gibberella fujikuroi and cephamycins by Streptomyces spp. In all these cases nitrogen must be exhausted before production of the secondary metabolite is initiated. Feedback Regulation It is shown in many examples in which the product

inhibits its further synthesis. An example is penicillin inhibition by lysine. Penicillin biosynthesis by Penicillium chrysogenum is affected by feedback inhibition by L-lysine because penicillin and lysine are end-products of a brack pathway (Fig. 6.9). Feedback by lysine inhibits the primary enzyme in the chain, homocitrate synthetase, and inhibits the production of -aminoadipate. The addition of -aminoadipate eliminates the inhibitory effect of lysine.

Self-inhibition by secondary metabolites: Several secondary products or even their analogues have been shown to inhibit their own production by a feedback mechanism. Examples are audorox, an antibiotic active against Gram-positive bacteria, and used in poultry feeds, chloramphenicol, penicillin, cycloheximids, and 6methylsallicylic acid (produced by Penicillium urticae). Chloramphenicol repression of its own production is shown in Fig. 6.10, which also shows chorismic acid inhibition by tryptophan.

ATP or Energy Charge Regulation of Secondary Metabolites Secondary metabolism has a much narrower tolerance for concentrations of inorganic phosphate than primary metabolism. A range of inorganic phosphate of 0.3-30 mM permits excellent growth of procaryotic and eucaryotic organisms. Average highest level that favors secondary metabolism is 1.0 mM while the average lower quantity that maximally suppresses secondary process is 10 mM High phosphate levels inhibit antibiotic formation hence the antibiotic industry empirically selects media of low

phosphate content, or reduce the phosphate content by adding phosphate complexing agents to the medium. Several explanations have been given for this phenomenon. Phosphate stimulates high respiration rate, DNA and RNA synthesis and glucose utilization, thus shifting the growth phase from the idiophase to the trophophase. This shift can occur no matter the stage of growth of the organisms. Exhaustion of the phosphate therefore helps trigger off idiophase.

Another hypothesis is that a high phosphate level shifts carbohydrate catabolism ways from HMP to the EMP pathway favoring glycolysis. If this is the case then NADPH would become limiting of idiolite synthesis. EMPIRICAL METHODS EMPLOYED TO DISORGANIZE REGULATORY MECHANISMS IN SECONDARY METABOLITE PRODUCTION Such methods include mutations and stimulation by the manipulation of media components and conditions.

(i) Mutations: Naturally occurring variants of organisms which have shown evidence of good productivity are subjected to mutations and the treated cells are selected randomly and tested for metabolite overproduction. The nature of the mutated gene is often not known. (ii) Stimulatory effect of precursors: Production is stimulated and yields increased by the addition of precursors. Penicillin production was stimulated by the addition

of phenylacetic acid present in corn steep liquor in the early days of penicillin fermentation. Methionine is required for synthesis of aflatoxin by Aspergillus parasiticus,. L-citurulline is required for mitomycin formation by Streptomyces verticillatus. (iii) Inorganic compounds: Phosphate and manganese. In summary, while high levels of phosphate encourage growth, they are detrimental to the production of secondary metabolites.

Manganese specifically encourages idiophase production particularly among bacilli, including the production of bacillin, bacitracin, mycobacillin, subtilin, D-glutamine, protective antigens and endospores. The amount needed are from 20 to several times the amount needed for growth. (iv) Temperature: Temperature range that permits good growth (in the trophophase) spans about 25C among microorganisms.

Temperature range within which secondary metabolites are produced is much lower, being in the order of only 5-10C. Sometimes two temperatures a higher for the trophophase and a lower for the idiophase are used.

Recently Viewed Presentations

  • Introduction to Biology

    Introduction to Biology

    Big Ideas in AP Biology. Big Idea 2: Biological systems utilize free energy and molecular building blocks to grow, to reproduce and to maintain dynamic homeostasis. Energy Transfer. life is an open system. organisms continuously interact with the environment.
  • Safety & Workers Compensation Coordinators Meeting (You Can

    Safety & Workers Compensation Coordinators Meeting (You Can

    Betsy Ramos Human Resources Department Salary Continuation Administration Manager Certificates of Appreciation Workers Compensation Automation System " You Can Make a Difference" "Those that made a difference" Solid Waste Management Safe Driver Awards Anthony Senegal, Jr. Achievement William Sherrard Achievement...
  • Arthurian Legends - Kingfishers English 8

    Arthurian Legends - Kingfishers English 8

    Alternate Assignment for Arthurian Legends Experts. Research and then create a mind-map for the Knights of the Round Table. Research and then create a mind-map for all the different variations (written, film, drama) of the Arthurian Legend
  • Amartya Sen: The Capabilities Approach Sundeep Sahay Amartya

    Amartya Sen: The Capabilities Approach Sundeep Sahay Amartya

    (Protecting this capability means protecting institutions that constitute and nourish such forms of affiliation, and also protecting the freedom of assembly and political speech.) Having the social bases of self-respect and non-humiliation; being able to be treated as a dignified...
  • Programmation des applications financières sous Excel en VBA

    Programmation des applications financières sous Excel en VBA

    Master Réseaux et Systèmes Distribués (RSD) Algorithmique des systèmes et applications réparties Introduction aux : Composants logiciels (JavaBeans)
  • Design and Development-Major. New Product to design variation.

    Design and Development-Major. New Product to design variation.

    Verify: In house- Mechanical endurance, Contact resistance, Time Interval,H.V, Megger, Shunt Coil, Charging Motor Resistance Value & Mechanical overall check. Validate: Type testing at IIT Chennai.
  • Treatment of dento - alveolar injuries

    Treatment of dento - alveolar injuries

    Unimmunized child can be protected by tetanus antitoxin. 2- Adequate debridment of the wound 1- stage of root formation 2- presence of root fractur 3- periapical radiolucencies 4- injury of the supporting periodontal membrane (degree of intrusion or extrusion o...
  • Hamlet Act I - Chandler Unified School District

    Hamlet Act I - Chandler Unified School District

    Do you agree? Group three: examine Hamlet's first soliloquy. How would you describe Hamlet? Why is his speech so pessimistic? "Mommy Dearest" Finally…. What kind of relationship does Hamlet have with his uncle and his mother? Explain. Act I, Scene...