Transcription

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - CiscoCisco Catalyst 2960-X and 2960-XR Series Switches Data SheetUpdated: September 5, 2017Document ID: 1453419102892274Find the right switchAnswer a few simple questions, and see the switches that t yourneeds.Get startedroduct Overviewisco Catalyst 2960-X and 2960-XR Series Switches are xed-con guration, stackable Gigabitthernet switches that provide enterprise-class access for campus and branch applications (Figure 1).esigned for operational simplicity to lower total cost of ownership, they enable scalable, secure andnergy-e cient business operations with intelligent services and a range of advanced Cisco IOS oftware features.igure 1.Cisco Catalyst 2960-X Series Switchesroduct Highlightsisco Catalyst 2960-X Series Switches feature: 24 or 48 Gigabit Ethernet ports with line-rate forwarding performance Gigabit Small Form-Factor Pluggable (SFP) or 10G SFP uplinks FlexStack-Extended capabilities for out-of-the wiring-closet distance stacking of up to 8 switcheswith 40 Gbps of stack throughput (optional) FlexStack-Plus for stacking of up to 8 switches with 80 Gbps of stack throughput (optional) Power over Ethernet Plus (PoE ) support with up to 740W of PoE budget 24-port PoE fanless switch for deployment outside the wiring closet Reduced power consumption and advanced energy management features USB and Ethernet management interfaces for simpli ed operations Application visibility and capacity planning with integrated Full (Flexible) NetFlow and NetFlow-Lite LAN Base or LAN Lite Cisco IOS software features Enhanced Limited Lifetime Warranty (E-LLW) o ering next-business-day hardware replacement Identify, classify and control of trusted internal network tra c through Domain Name System as anuthoritative Source (DNS-AS)isco Catalyst 2960-XR Series Switches also o er: Power resiliency with optional dual eld-replaceable power supplies IP Lite Cisco IOS software with dynamic routing and Layer 3 ata sheet c78-728232.html1/37

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - Ciscowitch Models and Con gurationsisco Catalyst 2960-X Series Switches include a single xed power supply and are available withither the Cisco IOS LAN Base or LAN Lite feature set. Cisco Catalyst 2960-XR Series Switches includeeld-replaceable modular power supply and can accommodate a second power supply. The Ciscoatalyst 2960-XR Series is available only with the Cisco IOS IP Lite feature set.able 1.Cisco Catalyst 2960-X Series Con gurationsModel10/100/1000EthernetportsUplink exStack-Plusand -L482 SFP LANBase740WYCiscoCatalyst2960X48LPD-L482 SFP LANBase370WYCiscoCatalyst2960X24PD-L242 SFP LANBase370WYCiscoCatalyst2960X48TD-L482 SFP LANBase-YCiscoCatalyst2960X24TD-L242 SFP LANBase-YCiscoCatalyst2960X48FPS-L484 SFPLANBase740WYCiscoCatalyst2960X48LPS-L484 SFPLANBase370WYCiscoCatalyst2960X24PS-L244 SFPLANBase370WYCiscoCatalyst2960X24PSQ-L24 (8 PoE)2 SFP,2 10/100/1000BTLANBase110W-Cisco484 ata sheet c78-728232.html2/37

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - -L244 SFPLANBase-YCiscoCatalyst2960X48TS-LL482 SFPLAN Lite--CiscoCatalyst2960X24TS-LL242 SFPLAN Lite--able 2.Cisco Catalyst 2960-XR Series Con plyFlexStackPlus 8FPD-I482 SFP IP Lite740W1025WACYCiscoCatalyst2960XR48LPD-I482 SFP IP Lite370W640WACYCiscoCatalyst2960XR24PD-I242 SFP IP Lite370W640WACYCiscoCatalyst2960XR48TD-I482 SFP IP Lite-250WACYCiscoCatalyst2960XR24TD-I242 SFP IP Lite-250WACYCiscoCatalyst2960XR48FPS-I484 SFPIP Lite740W1025WACYCiscoCatalyst484 SFPIP tches/data sheet c78-728232.html3/37

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - Cisco2960XR48LPS-ICiscoCatalyst2960XR24PS-I244 SFPIP Lite370W640WACYCiscoCatalyst2960XR48TS-I484 SFPIP Lite-250WACYCiscoCatalyst2960XR24TS-I244 SFPIP Lite-250WACYatalyst 2960-X Series Software Featuresll Catalyst 2960-X Series Switches use a single Universal Cisco IOS Software Image for all SKUs.epending on the switch model, the Cisco IOS image automatically con gures the LAN Lite, LAN Base,r IP Lite feature set.AN Lite models have reduced functionality and scalability for small deployments with basicequirements. Cisco Catalyst 2960-X Series Switches are available with the LAN Base and LAN Liteeature sets, and the Cisco Catalyst 2960-XR Series Switches are available with the IP Lite feature set.ote that each switch model is tied to a speci c feature level; LAN Lite cannot be upgraded to LANase and LAN Base cannot be upgraded to IP Lite.or more information about the features included in the LAN Lite, LAN Base and IP Lite feature sets,efer to Cisco Feature Navigator: co ONE Softwareisco ONE Software for Access Switching is available for the Cisco Catalyst 2960-X and 2960-XReries Switches.isco ONE Software is a new way for customers to purchase and use our infrastructure software. Iters a simpli ed consumption model, centered on common customer scenarios in the data center,WANs, and LANs.isco ONE Software and services provide customers with four primary bene ts: Software suites that address typical customer use scenarios at an attractive price Investment protection of their software purchase through software services-enabled licenseortability Access to ongoing innovation and new technology with Cisco Software Support Service (SWSS) Flexible licensing models to smoothly distribute customer's software spend over timeor ordering information for Cisco ONE Software for the Cisco Catalyst 2960-X and 2960-XR Serieswitches, go to e-access/switching-partumbers.html.isco Catalyst 2960-XR Series IP Lite High-Performance Routinghe Cisco hardware routing architecture delivers extremely high-performance IP routing in the Ciscoatalyst 2960-XR Series IP Lite Switches: IP unicast routing protocols (Static, Routing Information Protocol Version 1 [RIPv1], RIPv2,IPng, and EIGRP-Stub) are supported for network routing applications. Advanced IP unicast routing protocols (OSPF for Routed Access) are supported for loadalancing and constructing scalable LANs. IPv6 routing (OSPFv3) is supported in hardware formaximum performance. EIGRPv3-Stub and PIMv6-Stub are supported as a part of the IPv6 routing a sheet c78-728232.html4/37

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - Cisco Equal-cost routing facilitates Layer 3 load balancing and redundancy across the stack. Policy-Based Routing (PBR) allows superior control by facilitating ow redirection regardless of theouting protocol con gured (for both IPv4 and IPv6). Hot Standby Routing Protocol (HSRP) and Virtual Router Redundancy Protocol (VRRP) providesynamic load balancing and failover for routed links. Protocol Independent Multicast (PIM) for IP multicast is supported, including PIM Sparse ModePIM‑SM), PIM Dense Mode (PIM-DM), PIM sparse-dense mode and Source Speci c Multicast (SSM).etwork Securityhe Cisco Catalyst 2960-X and 2960-XR Series Switches provide a range of security features to limitccess to the network and mitigate threats, including: MAC-based VLAN assignment enables di erent users to authenticate on di erent VLANs. Thiseature enables each user to have a di erent data VLAN on the same interface. Cisco TrustSec uses SXP to simplify security and policy enforcement throughout the network. Formore information about Cisco TrustSec security solutions, visit cisco.com/go/TrustSec. Comprehensive 802.1X Features to control access to the network, including Flexibleuthentication, 802.1x Monitor Mode, and RADIUS Change of Authorization. IPv6 First-Hop Security enhances Layer-2 and Layer-3 network access from proliferating IPv6evices especially BYOD devices. It protects against rogue router advertisements, address spoo ng,ake DHCP replies and other risks introduced by IPv6 technology. Device Sensor and Device Classi er enable seamless versatile device pro les including BYODevices. They also enable Cisco Identity Services Engine (ISE) to provision identity based securityolicies. This feature is available on both the 2960-X and the 2960-XR product families. Cisco Trust Anchor Technology enables easy distribution of a single universal image for all modelsf 2960-X and 2960-XR Series by verifying the authenticity of IOS images. This technology allows thewitch to perform IOS integrity checks at boot-up by verifying the signature, verifying the Trusted Assetnder Management and authenticating the license. Cisco Threat Defense features including Port Security, Dynamic ARP Inspection, and IP Sourceuard. Private VLANs restrict tra c between hosts in a common segment by segregating tra c at Layer, turning a broadcast segment into a nonbroadcast multi access like segment. This feature is availablen the IP Lite feature set only. Private VLAN Edge provides security and isolation between switchports, which helps ensure that users cannot snoop on other users’ tra c. Unicast Reverse Path Forwarding (uRPF) feature helps mitigate problems caused by thentroduction of malformed or forged (spoofed) IP source address into a network by discarding IPackets that lack a veri able IP source address. This feature is available in the IP Lite feature set only. Multidomain Authentication allows an IP phone and a PC to authenticate on the same switch portwhile placing them on appropriate voice and data VLAN. Access Control Lists (ACLs) for IPv6 and IPv4 for security and QoS ACEs. VLAN ACLs on all VLANs prevent unauthorized data ows from being bridgedwithin VLANs. Router ACLs de ne security policies on routed interfaces for controlplane and data-plane tra c. IPv6 ACLs can be applied to lter IPv6tra c. Port-based ACLs for Layer 2 interfaces allow security policies to be appliedon individual switch ports. Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3SNMPv3) provide network security by encrypting administrator tra c during Telnet and SNMPessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a specialryptographic software image because of U.S. export restrictions. Switched Port Analyzer (SPAN), with bidirectional data support, allows Cisco Intrusion Detectionystem (IDS) to take action when an intruder is detected. TACACS and RADIUS authentication facilitates centralized control of the switch and restrictsnauthorized users from altering the con data sheet c78-728232.html5/37

07/11/2017Cisco Catalyst 2960-X and 2960-XR Series Switches Data Sheet - Cisco MAC Address Noti cation allows administrators to be noti ed of users added to or removed fromhe network. Multilevel security on console access prevents unauthorized users from altering the switchon guration. Bridge protocol data unit (BPDU) Guard shuts down Spanning Tree Port Fast-enabled interfaceswhen BPDUs are received to avoid accidental topology loops. Spanning Tree Root Guard (STRG) prevents edge devices not in the network administrator’sontrol from becoming Spanning Tree Protocol root nodes. IGMP ltering provides multicast authentication by ltering out nonsubscribers and limits theumber of concurrent multicast streams available per port. Dynamic VLAN assignment is supported through implementation of VLAN Membership Policyerver client capability to provide exibility in assigning ports to VLANs. Dynamic VLAN facilitates theast assignment of IP addresses.edundancy and Resiliencyisco Catalyst 2960-X and 2960-XR Series Switches o er a number of redundancy and resiliencyeatures to prevent outages and help ensure that the network remains available: Cross-stack EtherChannel provides the ability to con gure Cisco EtherChannel technology acrossi erent members of the stack for high resiliency. Flexlink provides link redundancy with convergence time less than 100 milliseconds. IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree ProtocolMSTP) provide rapid spanning-tree convergence independent of spanning-tree timers and also o erhe bene t of Layer 2 load balancing and distributed processing. Stacked units behave as a singlepanning-tree node. Per-VLAN Rapid Spanning Tree (PVRST ) allows rapid spanning-tree reconvergence on a perLAN spanning-tree basis, without requiring the implementation of spanning-tree instances. Cisco Hot Standby Router Protocol (HSRP) is supported to create redundant, fail safe routingopologies in 2960-XR Series IP Lite SKUs. Switch-port auto-recovery (Error Disable) automatically attempts to reactivate a link that isisabled because of a network error. Power redundancy with an optional second power supply on 2960-XR Series models, or with anxternal RPS on 2960-X Series models.nhanced Quality of Servicehe Cisco Catalyst 2960-X and 2960-XR Series Switches o er intelligent tra c management thateeps everything owing smoothly. Flexible mechanisms for marking, classi cation, and schedulingeliver superior performance for data, voice, and video tra c, all at wire speed. Primary QoS featuresnclude: Up to eight egress queues per port and strict priority queuing so that the highest priority packetsre service