Transcription

Better Air is Our Business PerfectPleatPerfectPleat M8PerfectPleat ULTRA 4" Extended Surface Pleated Filters Mechanical efficiency — does not rely on electretcharge technology Form and fit unlike any other 4" pleat Patented media with controlled fiber size and blend MERV 7 - available in Standard modelPerfectPleat ULTRA MERV 8 - available in M8 and ULTRA modelsPerfectPleat M8 ULTRA made with antimicrobialPerfectPleat Covered under one or more of the following patents:US 6398839 B2; US 6254653 B1; US6159318; US 6165242;US6387140 B1AAF International proudly offers the 4" PerfectPleat - the best 4"pleated filter in the industry. The 4" PerfectPleat offers the sameconsistent pleat spacing and rugged durability characteristic of thehighly successful 2" models, with advancements that add even morestrength resulting in one very tough filter.Design and ConstructionAAF engineers drew upon years of experience in filter manufacturingto design a 4" filter worthy of the PerfectPleat name. Each modelplaces a DuraFlex media pack inside of a two piece frame. Strapsare added to the air-entering side of the filter to help maintain pleatspacing, while specially designed pleat spacers are inserted in multiplerows on the air-leaving side. The pleat spacers also assist in keepingthe pleats open during use,maximizing filter life. The two-pieceframe is then assembled around therigid media pack and is bonded atall contact points with adhesivesthat ensure resistance to moisture.The result is fit and finish unlikeanything available in a 4" pleatcoupled with excellent strengthand durability. All framecomponents, straps, and pleatspacers are constructed of .028beverage containerboard withthe highest wet-strength available.DuraFlex - AAF’s Patented MediaUniform size virgin fibers are assembled in closely controlledblends to create a media that is both self-supporting and consistentin performance. The self-supporting characteristics allow a pleatingpattern that promotes excellent dust holding and low initial resistance.DuraFlex media requires no wire support to maintain its shape.No wire means that the all 4" PerfectPleats are totally incinerable.Efficiency and PerformancePerfectPleat 4" offers the efficiency and low initial resistance that youexpect and require. PerfectPleat is rated MERV 7 and has 9 pleats perfoot (PPF). PerfectPleat M8 and ULTRA are rated MERV 8 and have11 PPF. (See chart on page 2 for additional performance data.)ApplicationsThe 4" PerfectPleats are ideal for any application where pleated filtersare in use. These filters are an excellent choice when upgrading tohigher efficiencies where 2" pleated filters are used, particularly infront loading frames. The 4" PerfectPleats can be used as final filtersin single bank housings.Every PerfectPleat will provide excellent performance and durabilitywhen properly installed and maintained.All PerfectPleat models have a die-cutframe on the air-entering side.

PerfectPleat , PerfectPleat M8, PerfectPleat ULTRA Product Information (Standard Sizes)Nominal Sizes*(Inches)(W x H x D)12 x 24 x 416 x 20 x 416 x 25 x 418 x 24 x 420 x 20 x 420 x 25 x 424 x 20 x 424 x 24 x 425 x 29 x 4Rated Airflow CapacityMedia Area(SCFM)(sq. ft.)Pleats Per Filter500 FPM 625 FPM PerfectPleat PerfectPleat M8 PerfectPleat ULTRA PerfectPleat PerfectPleat M8 PerfectPleat ULTRAActual Sizes(Inches)(W x H x D)11 3/8 x 23 3/8 x 3 3/415 3/8 x 19 3/8 x 3 3/415 3/8 x 24 3/8 x 3 3/417 3/8 x 23 3/8 x 3 3/419 3/8 x 19 3/8 x 3 3/419 3/8 x 24 3/8 x 3 3/423 3/8 x 19 3/8 x 3 3/423 3/8 x 23 3/8 x 3 3/424 3/8 x 28 3/8 x 3 14.213.917.519.418.222.922.027.235.0PerfectPleat filters are classified UL Class 2. Testing was performed according to UL Standard 900 and CAN 4-S111.Performance DataFilterPleatsPerLineal FootPerfectPleat 4"PerfectPleat M8 4"PerfectPleat ULTRA 4"91111Rated Initial Resistance(in. w.g.)500 FPM 625 FPM.27.26.26.37.37.37RecommendedFinal Resistance(in. w.g.)ASHRAE 52.2MERV1.01.01.0788Composite Minimum Efficiency200 200 200 93 93 93 Resistance to AirflowEfficiency vs. Particle SizeResistance (in. w.g.)Filtration Efficiency (%)Continuous OperatingTemperature Limits F CParticle Diameter (micrometers)Airflow (FPM)PerfectPleatPerfectPleat M8 and ULTRA10300 Ormsby Park Place Suite 600Louisville, Kentucky 40223-6169www.aafintl.comCustomer Service 888.AAF.2003Fax 888.223.6500AFP-1-206BSEP ‘08QG 5MAAF has a policy of continuous product research andimprovement and reserves the right to changedesign and specifications without notice.ISO Certified 9001:2000 2008 AAF InternationalThe USGBC Member logo is a trademark owned by theU.S. Green Building Council and is used by permission.

Better Air is Our BusinessDriPak Extended Surface Pocket Filters Fiberglass Media Patented pocket design lengthens filter life Low resistance and high dust holding capacity Engineered for performance reliability Available in two efficiencies: MERV 15 (90-95%)and MERV 13 (80-85%)DriPak filters meet efficiency requirementsestablished for LEED Project Certification.DriPak Designed for high performance in demanding operating conditions,the DriPak extended surface pocket filters are perfect as prefiltersand final filters for particulate removal where clean air is required.DriPak filters are an excellent choice for healthcare facilities,automotive paint booths, commercial buildings, and variousindustrial applications. Manufactured by AAF International,the original developers of the extended surface pocket filter,DriPak has set the industry standard for over 40 years.Aerodynamically Balanced PocketsThe DriPak pocket design has been aerodynamically balanced(U.S. Patent 4,356,011) to achieve optimum pocket configurationfor minimum resistance and maximum dust holding capacity. Thisbalancing significantly lengthens the life of the filter. Our contouredpockets allow full inflation without crowding or restriction of airflow.ScrimIAQ EngineeredDriPak is available in a wide range of sizes and two efficiencies –MERV 15 (90-95%) and MERV 13 (80-85%). Micro-fine fiberglass fibersprotected by a thin layer of scrim, offer low resistance at a high levelof cleaning efficiency. Smaller sized fibers are used to produce highefficiency medias such as MERV 15 (90-95%) and MERV 13 (80-85%).Designed for PerformanceDriPak employs a sturdy, leak-free pocket design to prevent collectedparticulate from escaping. The design includes span stitching coveredwith a thermoplastic sealant to hold the stitches in place and seal theneedle holes. Interlocked support frames attached to the pocketsprevent flexing and buckling during full inflation. The double U-shapedreinforced header forms a solid container for the pocket support frames.To ensure quality performance, DriPak filters are tested in an AAFapproved, state-of-the-art laboratory, governed by ISO-9001 d Pocket Support FramesStitchingAirflowLeak-free Span Stitching

DriPak Performance InformationInitial Resistance (Pa)Initial Resistance (in. w.g.)Initial Resistance vs. AirflowAirflow VelocityCurves based on 24"x24"x30", 8 pocket filter.Particle Size Removal Efficiency (%)Composite Minimum Efficiency CurveParticle Diameter (μm)Tested in accordance with ASHRAE Standard 52.2.This chart shows the minimum efficiency the filter willprovide throughout its service life. Dust-spot efficiencyestablished using ASHRAE Test Standard 52.1Particle Size (μm)10300 Ormsby Park Place Suite 600Louisville, Kentucky 40223-6169www.aafintl.comCustomer Service 888.AAF.2003Fax 888.223.6500AFP-1-120CNOV ‘08QG 3MAAF has a policy of continuous product research andimprovement and reserves the right to changedesign and specifications without notice.ISO Certified 9001:2000 2008 AAF InternationalUSGBC Member logo and LEED are trademarks owned bythe U.S. Green Building Council and are used by permission.

Better Air is Our Business BioCel I High Efficiency Extended Surface Air FilterThe BioCel I filter was designed primarily to remove airbornebiological contaminants in hospital critical areas and food andpharmaceutical processing plants. It has also been engineeredto meet the exacting requirements of precision manufacturingoperations and laboratories where very high efficiency filtrationof fine particulate matter is necessary.BioCel I filters meet efficiencyrequirements established for LEED Project Certification.High Efficiency - Low ResistanceThe air cleaning efficiency of the BioCel I is significantly higherthan that of 90-95% ASHRAE efficiency filters. BioCel I exceedsthe maximum efficiency of 98% which can be measured byASHRAE 52.1 test method.Rated at 95% efficiency on 0.3 micrometer challenge aerosol andMERV 16 by ASHRAE Standard 52.2, BioCel I has the advantageof much lower pressure drop than a typical HEPA filter (0.4" versus1.0" w.g. at 250 FPM). BioCel I fills the gap between ASHRAE gradehigh efficiency filters and ultra-high efficiency HEPAs at half the weightand pressure drop.This compact, lightweight filter will withstand operating temperaturesto 350 F, if recommended final resistance is not exceeded.To maximize filter life, use BioCel I with high quality AAF prefilters.ConstructionBioCel I filters consist of a pleated media pack enclosed in agalvanized steel frame assembly. The media is made of ultra-finefiberglass formed into a series of pleats. Corrugated aluminumseparators maintain uniform spacing between each pleat to allowunrestricted airflow through the filter. Bar braces are installed onboth sides of the filter for extra reinforcement of the media pack.A flattened, expanded metal faceguard installed on both sides ofthe filter is available as an option.BioCel I filters have a single piece galvanized steel header on the airentering side that is interlocked to the cell sides in a patented fashionthat prevents leakage and forms a totally rigid construction.Ideal for Variable Volume SystemsDue to the rigid all metal construction and water resistant mediain a supported pleat type configuration, BioCel I filters can be usedin systems with difficult operating conditions: Variable air volume Turbulent airflow Repeated fan shutdown High temperature High humidity Intermittent exposure to water such as sea coast installationsBioCel M-Pak – A New AlternativeBioCel M-Pak offers the same media area and pressuredrop as the BioCel I in a 6" deep, high-impact polystyrenecell side.BioCel M-Pak offers several advantages in comparisonto BioCel I. Lighter – 1/ 2 the weight Requires less storage space Reduces disposal costs Easier handling Fully IncinerableFor more information onBioCel M-Pak see brochure AFP-1-117.

BioCel I Product InformationNominal Size(Inches)(W x H x D)RatedAirflow Capacity(CFM)125 FPM 250 FPM 500 FPMActual Size(Inches)(W x H x D)RatedInitial Resistance(in. w.g.)125 FPM 250 FPM 500 FPMGrossMediaArea(sq. ft.)Filters ShippingPerWeightCarton (lbs.)95% Initial Efficiency (0.3μm Particles)(a)(a)24 x 24 x 1223 /8 x 23 /8 x 11 /250010002000.19.40.95156120.024 x 24 x 1224 x 24 x 11 /250010002000.19.40.95165121.524 x 20 x 1223 3/8 x 19 3/8 x 11 1/24138251650.19.40.95127117.020 x 24 x 1219 /8 x 23 /8 x 11 /24138251650.19.40.95127118.512 x 24 x 1211 3/8 x 23 3/8 x 11 1/22505001000.19.40.9572112.03311331Recommended Final Resistance 2.0 in. w.g.(a)(a)24 x 24 x 623 3/8 x 23 3/8 x 5 7/85001000—.30.60—93222.024 x 24 x 624 x 24 x 5 7/85001000—.30.60—98224.024 x 20 x 623 /8 x 19 /8 x 5 /8413825—.30.60—93222.020 x 24 x 619 /8 x 23 /8 x 5 /8413825—.30.60—96221.512 x 24 x 611 3/8 x 23 3/8 x 5 7/8250500—.30.60—42214.0333377Recommended Final Resistance 1.5 in. w.g.(a) Available in double header construction only.Metric Conversion Info1.0 in. 2.54 cm1 CFM 1.7 m 3 / hr221 ft .09 m1.0 in. w.g. 249 Pa1 FPM .005 m/sec.Performance Data Double header construction isavailable for installation intoother manufacturers' framingsystems.Initial Efficiency vs.Particle DiameterAt rated airflow the BioCel I hasefficiency of 95% on 0.3 micronparticles and is classifiedMERV 16 in accordance withASHRAE Standard 52.2. 6" or 12" depths available. HEPA filter constructionavailable. See BulletinAFP-1-110.Underwriters Laboratories,Inc. ClassificationBioCel I filters are classifiedClass 1. Testing was performedaccording to UL Standard 900.10080Fractional Efficiency (%)Options60402000. 1.2.4.6.812468 10Particle Diameter (micrometers) LEED is a registered trademark of the US Green Building Council.10300 Ormsby Park Place Suite 600Louisville, Kentucky 40223-6169www.aafintl.comCustomer Service 888.AAF.2003Fax 888.223.6500AFP-1-116TNOV ‘08QG 5MASHRAE 52.2 Composite Minimum Efficiency CurveAAF has a policy of continuous product research andimprovement and reserves the right to changedesign and specifications without notice.ISO Certified 9001:2000 2008 AAF InternationalThe USGBC Member logo is a trademark owned by theU.S. Green Building Council and is used by permission.