Transcription

STRUCTURAL GENERAL NOTESF. THE ARCHITECTURAL DRAWINGS SHALL BE USED IN CONJUNCTIONWITH THESE STRUCTURAL DRAWINGS FOR DETAIL DIMENSIONS ANDSECTION DETAILS AS REQUIRED.A. ALL CONSTRUCTION SHALL CONFORM WITH THE PROVISIONS OF THE2009 IBC AND ASCE 7-05 MINIMUM DESIGN LOADS FOR BUILDINGS ANDOTHER STRUCTURES.B. STEEL PROCUREMENT ACT: ALL STEEL PRODUCTS BEING PROVIED FORPERMANENT INCLUSION IN THE PROJECT ARE TO BE MADE IN THE UNITEDSTATES IN ACCORDANCE WITH THE STEEL PROCUREMENT ACT, ANDCERTIFICATES OF COMPLIANCE FROM EACH SUPPLIER FOR ALL STEELPRODUCTS DELIVERED TO THE PROJECT SHALL BE SUBMITTED AS REQUIREDBY THE ACT.2. DESIGN LOADINGK. CONTRACTOR IS REQUIRED TO PROVIDE SHEETING, SHORING ANDBRACING AS NECESSARY TO MAINTAIN STABILITY OF EXCAVATIONAND ADJACENT PROPERTY.1ST CONCRETE FLOOR8" CONC. SLAB NORMAL WT. -- 100 PSFPLAZA - MISC. LOADMECHANICAL -----------------------ELECTRICAL/LIGHTING ---------CEILING -------------------------------MISCELLANEOUS ------------------5 PSF3 PSF2 PSF2 PSFTOTAL ---------------------------------20 PSFPLAZA - 2 WAY SLAB4. FOUNDATIONMECHANICAL -----------------------ELECTRICAL/LIGHTING ---------CEILING -------------------------------MISCELLANEOUS -----------------INFILL MATERIAL ------------------5 PSF3 PSF2 PSF2 PSF80 PSFTOTAL ---------------------------------92 PSF12" CONC. SLAB NORMAL WT. - 150 PSFSTAIR 4 LANDINGSTAIR 4 TREADS3" CONCRETE ------------------------PORCELAIN TILE ---------------------FRAMING -------------------------------CEILING/LIGHTS ---------------------SPRINKLERS --------------------------MISCELLANEOUS ---------------------37.5 PSF23 PSF5 PSF3 PSF2 PSF2.5 PSF2" CONCRETE FILLED TREADS--PORCELAIN TILE ---------------------FRAMING -------------------------------CEILING/LIGHTS ---------------------SPRINKLERS --------------------------MISCELLANEOUS ---------------------25 PSF23 PSF5 PSF3 PSF2 PSF2 PSFTOTAL ---------------------------------73 PSFTOTAL ---------------------------------60 PSFWALL SYSTEMCURTAIN WALL --------------------6" PRECAST WALL SYSTEM ---8" PRECAST WALL SYSTEM ---BRICK WALL SYSTEM-------------20 PSF75 PSF100 PSF40 PSFELEVATED FLOORH. CONSULT ARCHITECTURAL, MECHANICAL AND ELECTRICAL DRAWINGSFOR VERIFICATION OF LOCATION AND DIMENSION OF CHASES, INSERTS,OPENINGS, SLEEVES. WASHERS, DRIPS, REVEALS, DEPRESSIONS ANDOTHER PROJECT REQUIREMENTS.J. THE STRUCTURAL CONTRACT DOCUMENTS ARE NOT TO BEREPRODUCED FOR USE AS SHOP DRAWINGS.A. THE DESIGN DEAD LOAD FOR THE FRAMING IS AS FOLLOWS:1ST FLOOR MISC. LOADG. AT THE TIME OF SHOP DRAWING SUBMISSION, THE GENERALCONTRACTOR SHALL INFORM THE ENGINEER, IN WRITING, OF ANYDEVIATIONS OR OMISSIONS FROM THE CONTRACT DOCUMENTS.MAIL ROOM ROOF SLAB5" LW SLAB & 1 1/2" DECK -----FRAMING -----------------------------MECHANICAL -----------------------ELECTRICAL/LIGHTING ---------CEILING -------------------------------MISCELLANEOUS ------------------43 PSF5 PSF5 PSF3 PSF2 PSF2 PSF5" NW SLAB & 1 1/2" DECK -----FRAMING -----------------------------MECHANICAL -----------------------ELECTRICAL/LIGHTING ---------CEILING -------------------------------MISCELLANEOUS ------------------53 PSF5 PSF5 PSF3 PSF2 PSF2 PSFTOTAL ---------------------------------60 PSFTOTAL ---------------------------------70 PSFA. BOTTOM OF ALL EXTERIOR FOOTINGS SHALL BE A MINIMUM OF4'-0" BELOW FINISH GRADE FOR FROST PROTECTION, UNLESSNOTED OTHERWISE ON THE DRAWINGS. SEE SITE PLANS FOREXISTING AND FINISHED GRADES.B. TOP OF ALL INTERIOR FOOTINGS SHALL BE 8" BELOW FINISHEDFLOOR , UNLESS NOTED OTHERWISE ON THE DRAWINGS.C. ALL FOOTINGS HAVE BEEN DESIGNED FOR AN ALLOWABLE NETSOIL BEARING PRESSURE OF 4,000 PSF. IT SHALL BE THECONTRACTOR'S RESPONSIBILITY TO SECURE THE SERVICES OFA GEOTECHNICAL ENGINEER FOR FIELD VERIFICATION OF THESOIL BEARING PRESSURES. SHOULD THE SOIL BEARINGPRESSURE BE FOUND TO BE LESS THAN 4,000 PSF THECONTRACTOR SHALL IMMEDIATELY NOTIFY THE ARCHITECT.D. ALL EXCAVATION, BACKFILLING, AND FILLING OPERATIONSBENEATH THE BUILDING SLAB AND FOUNDATIONS, AND ALLCOMPACTION TESTS AND INSPECTION, SHALL BE DONE UNDER THEDIRECTION AND SUPERVISION OF A REGISTERED GEOTECHNICALENGINEER RETAINED BY THE CONTRACTOR. ALL SOIL, EQUIPMENTAND PROCEDURES SHALL BE APPROVED BY THE GEOTECHENGINEER PRIOR TO ALL EARTHWORK OPERATIONS.E. ALL FILL UNDER FOOTINGS AND SLABS SHALL BE COMPACTED TOA DRY DENSITY OF 100 PERCENT OF MAXIMUM DRY DENSITY ASDETERMINED BY ASTM D 698. OVEREXCAVATION REQUIRED AT COLUMNFOOTINGS CAN BE BACKFILLED USING PENNDOT 2A STONE COMPACTEDOR FLOWABLE FILL WITH A MIN. 28 DAY COMPRESSIVE STRENGTH OF300 PSF.TYPICAL FOUNDATION BEARING SHALL BE PREPARED PER FOLLOWING:GEOTECHNICAL NTROOFDECK & INSULATION -----------FRAMING ---------------------------MECHANICAL ---------------------ELECTRICAL/LIGHTING -------CEILING -----------------------------MISCELLANEOUS ----------------5 PSF5 PSF5 PSF3 PSF2 PSF5 PSFTOTAL --------------------------------25 PSFBEARING MATERIALDESIGN LIVE LOADS ARE AS FOLLOWS:RESIDENTIAL -----------CORRIDORS 1ST -CORRIDORS ABOVE 1ST FLOOR-----------------------------------GROUND FLOOR / COMMON AREAS ----------------------------MAIL ROOM ------------LOADING DOCK ---------MECHANICAL ------------STAIRS ---------------------ROOF -----------------------PLAZA ----------------------WIND (3 SECOND --WIND EXPOSURE D IMPORTANCE FACTOR ---------------------------------------OCCUPANCY CATEGORY --------------------------------------------SNOW EXPOSURE FACTOR -----------------------------------------SNOW IMPORTANCE FACTOR --------------------------------------THREMAL FACTOR ----BUILDING OCCUPANCY CATEGORY-------------------------------SEISMIC USE GROUP -SEISMIC IMPORTANCE FACTOR -----------------------------------MAPPED SPECTRAL RESPONSE ACCELERATION -----------SEISMIC DESIGN CATEGORY ---------------------------------------SITE CLASS --------------BASIC SEISMIC FORCE RESISTING SYSTEM ------------------RESPONSE MODIFICATION COEFFICIENT ---------------------DESIGN BASE SHEAR ANALYSIS PROCEDURE -----------------------------------------------40 PSF100 PSF80 PSF100 PSF100 PSF100 PSF150 PSF100 PSFPf 30 PSF PLUS SNOW DRIFTINGPg 35 PSF100 PSF90 MPHEXPOSURE BIw 1.15IIICe 0.9Is 1.1Ct 1.0IIIIIIe 1.25SDS 0.148qSDI 0.088qBDCOMBINATION OFCONCENTRIC BRACING& CONC. SHEAR WALLSR 5500 KIPSEQUIVALENT LATERALFORCE PROCEDURETHE CONTRACTOR IS CAUTIONED AS TO NOT STORE ANY CONSTRUCTIONMATERIALS OR UNDERTAKE ANY CONSTRUCTION OPERATION WHICH WILLEXCEED THE DESIGN LIVE LOAD CAPACITIES NOTED.B.C.D.THE STRUCTURE HAS BEEN DESIGNED FOR THE DEAD AND LIVELOADS INDICATED ABOVE. ANY INCREASE OF LOADS DUE TOCHANGE IN USAGE OR CONSTRUCTION MATERIALS, ETC. SHALLHAVE THE WRITTEN APPROVAL OF THE ENGINEER.INTACT SHALE/SILTSTONEBEDROCK (1)NONEIN-SITU FILL OR NATURALSOILS1/3BCOMPACTED STRUCTURALFILL (2)1/4BNONE1B1/2BF. PROVIDE 6" COMPACTED STONE BASE BELOW SLABS ON GRADE.STONE SHALL CONFORM TO PENNDOT 2A.G. REFERENCE GEOTECHNICAL REPORT PREPARED BY:CMT LABORATORIES, INC.2701 CAROLEAN INDUSTRIAL DR.STATE COLLEGE, PA 16801DATED: AUGUST 3, 20155. CAST-IN-PLACE CONCRETEA. ALL CONCRETE WORK SHALL CONFORM TO ALL PROVISIONS OF THE"SPECIFICATIONS FOR STRUCTURAL CONCRETE FOR BUILDINGS"(ACI 301), AND TO THE "BUILDING CODE REQUIREMENTS FORREINFORCED CONCRETE" (ACI 318).ADDITIONALLY THE CONCRETE SHALL CONFORM TO ALL PROVISIONSOF THE LATEST EDITIONS OF THE FOLLOWING PUBLICATIONS:1. ACI 305R RECOMMENDED PRACTICE FOR HOT WEATHERCONCRETING.2. ACI 306R RECOMMENDED PRACTICE FOR COLD WEATHERCONCRETING.3. ACI 347 RECOMMENDED PRACTICE FOR CONCRETEFORMWORK.C.F. PROVIDE SOLID BLOCK OR FILL WALL SOLID WITH GROUTDIRECTLY BELOW ALL CHANGES IN WALL THICKNESS ORCONSTRUCTION AS REQUIRED TO PROVIDE CONTINUOUS BEARINGFOR ALL FACE SHELLS OF BLOCK.G. LAP ALL VERTICAL REINFORCING 48 BAR DIAMETERS MINIMUM.H. PROVIDE 8" DEEP SOLID BEARING BELOW ALL STUDSBEARING ON MASONRY WALLS. SOLID BEARING SHALL BE SOLIDBLOCK OR BRICK OR HOLLOW BLOCK FILLED SOLID WITH GROUT.J. PROVIDE A SOFT JOINT WHERE ANY NON-BEARING MASONRYPARTITIONS OR WALLS ARE LAID TO THE UNDERSIDE OF THESTRUCTURAL FLOOR OR ROOF FRAMING ABOVE.K. ALL REINFORCING STEEL SHALL CONFORM TO ASTM A615, GRADE 60.L. INSPECTION AND TESTING SHALL BE PERFORMED AS REQUIRED BYSPECIFICATIONS.7A. STRUCTURAL AND MISCELLANEOUS STEELA. ALL STRUCTURAL AND MISCELLANEOUS STEEL SHALL CONFORM TOTHE THIRTEENTH EDITION OF THE AISC "SPECIFICATION FOR THEDESIGN, FABRICATION AND ERECTION OF STRUCTURAL STEELFOR BUILDINGS" AND ALL ITS SUPPLEMENTS, AND TO THE AISC"CODE OF STANDARD PRACTICE FOR STEEL BUILDINGS ANDBRIDGES." STRUCTURAL STEEL DESIGN BASED ON LRFD PROCEDURE.B. THE STRUCTURAL STEEL ERECTER WILL BE RESPONSIBLE FORPROVIDING ADEQUATE TEMPORARY BRACING DURING CONSTRUCTIONTO PREVENT COLLAPSE DURING CONSTRUCTION.C. ALL STRUCTURAL STEEL BEAMS AND COLUMNS SHALL CONFORM TOASTM A-572 FY 50,000 PSI UNLESS NOTED OTHERWISE. ALL ANGLES,CHANNELS AND MISCELLANEOUS STEEL SHALL CONFORM TO ASTMA-36, FY 36,000 PSI.D. STEEL TUBES SHALL CONFORM TO ASTM A500 GRADE B, FY 46,000 PSI.E. ALL STEEL PIPE SHALL CONFORM TO ASTM A-501, FY 36,000PSI OR ASTM A-53 TYPE "E" OR "S" GRADE B, FY 35,000 PSI.F. ALL WELDED CONNECTIONS SHALL BE DONE WITH E70XX ELECTRODESWITH 3/16" MINIMUM MATERIAL. ALL BOLTED CONNECTIONS SHALLUSE 3/4" DIA. ASTM A325N HIGH STRENGTH BOLTS MINIMUM. ALLBEAM CONNECTIONS SHALL DEVELOP THE GREATER SHEAR VALUE OFONE HALF OF ITS TOTAL UNIFORM LOAD CAPACITY IN ACCORDANCEWITH THE AISC SPECIFICATIONS FOR FRAMED BEAM CONNECTIONS,TABLE 3-6, OR THE END REACTION LISTED. IF SHOP WELDED, FURNISHIN ACCORDANCE WITH TABLE 10-3. MINIMUM THICKNESS OF CLIP ANGLESOF 5/16". NO CONNECTIONS SHALL BE MADE USING LESS THAN TWOBOLTS. ALL ANCHOR BOLTS SHALL BE ASTM A-307 U.N.O. ALLCONNECTIONS SHALL BE DEVELOPED BY THE CONTRACTOR UNLESSCOMPLETELY DETAILED ON CONTRACT DRAWINGS.THE STRUCTURAL STEEL FABRICATOR SHALL PROVIDE CERTIFICATIONBY A PROFESSIONAL ENGINEER, REGISTERED IN THE COMMONWEALTHOF PENNSYLVANIA THAT THE CONNECTION DESIGN IS IN ACCORDANCEWITH ALL APPLICABLE CODES AND SPECIFICATIONS.SPREAD/COLUMN CONTINUOUS WALLFOOTINGFOOTINGB FOOTING WIDTH1 FIELD VERIFIED BY GEOTECHNICAL ENGINEER-OF-RECORD2 MAY BE REDUCED AFTER FIELD INSPECTION BY GEOTECHNICALENGINEER-OF-RECORDB.E. PROVIDE 8" MINIMUM DEPTH OF 100% SOLID MASONRY OR HOLLOWBLOCK FILLED SOLID WITH GROUT BELOW ALL BEAMS OR LINTELS.ALL CONCRETE, UNLESS NOTED OTHERWISE, SHALL BE STONEAGGREGATE CONCRETE HAVING A MINIMUM COMPRESSIVE STRENGTHOF 4,000 PSI AT 28 DAYS.1. 1ST FLOOR CONCRETE SLAB AND BEAMS - NORMAL WEIGHTCONCRETE WITH A MINIMUM DESIGN COMPRESSION STRENGTHOF 4000 PSI AT 28 DAYS.2. ALL CONCRETE SLAB ON METAL DECK SHALL BE LIGHT WEIGHTSTRUCTURAL CONCRETE HAVING A MINIMUM DESIGN COMPRESSIONSTRENGTH OF 4000 PSI AT 28 DAYS.G. END CONNECTIONS OF COMPOSITE FLOOR BEAMS SHALL DEVELOP INSHEAR THE END REACTIONS INDICATED ON THE DRAWINGS.H. SHOP AND FIELD WELDS SHALL BE MADE BY APPROVED CERTIFIEDWELDERS AND SHALL CONFORM TO THE AMERICAN WELDING SOCIETYCODE FOR BUILDINGS AWS D1.1. WELDS SHALL DEVELOP THEFULL STRENGTH OF MATERIALS BEING WELDED, UNLESS OTHERWISENOTED.J. ALL EXPANSION BOLTS SHALL BE HILTI KWIK BOLT 3 EXPANSION ANCHORS,3" MINIMUM EMBEDMENT LENGTH AS MANUFACTURED BY HILTIOR APPROVED EQUIVALENT. U.N.O. ALL EXPANSION BOLTS SHALL BESET IN CONCRETE OR 100% SOLID FILLED MASONRY.K. NO OPENINGS IN BEAMS SHALL BE PERMITTED WITHOUT THE WRITTENPERMISSION OF THE ARCHITECT.L. THE USE OF A GAS TORCH IN THE FIELD FOR CUTTINGHOLES OR FOR CORRECTING FABRICATION ERRORS WILL NOT BEPERMITTED ON STRUCTURAL FRAMING MEMBERS EXCEPT WITH THEWRITTEN APPROVAL OF THE ARCHITECT FOR EACH SPECIFICCONDITION.M. ALL STRUCTURAL STEEL THAT IS TO BE FIREPROOFED SHALL NOT BE PAINTED.STRUCTURAL STEEL NOT REQUIRED TO BE FIREPROOFED SHALL BE SHOPPAINTED WITH AN APPROVED CORROSION RESISTANT PRIMER. STEEL SHALLBE PAINTED IN STRICT ACCORDANCE WITH THE AISC SPECIFICATIONS ANDMANUFACTURER'S RECOMMENDATIONS. PRIOR TO PAINTING, ALL STEELSURFACES SHALL BE PREPARED IN ACCORDANCE WITH SSPC-SP3. ALLPAINTS SHALL BE APPROVED BY THE ARCHITECT PRIOR TO THEIR USE.STRUCTURAL STEEL EXPOSED TO WEATHER SHALL BE HOT-DIP GALVANIZED.C. SHOP DRAWINGS FOR ALL STRUCTURAL ELEMENTS SHOWN ON THECONTRACT DOCUMENTS MUST BE SUBMITTED BY THE GENERALCONTRACTOR AND REVIEWED BY THE ENGINEER. IF THECONTRACTOR OR OWNER FAILS TO OBTAIN ENGINEER'S REVIEW OFTHE SHOP DRAWINGS, THE ENGINEER WILL NOT BE RESPONSIBLEFOR THE STRUCTURAL CERTIFICATION AND DESIGN OF THEPROJECT. SHOP DRAWINGS ARE REVIEWED BY THE ENGINEER ASA CONVENIENCE TO THE GENERAL CONTRACTOR AND ARE NOT ACONTRACT DOCUMENT.D. LOADS GREATER THAN THE DESIGN LIVE LOADS SHALL NOT BEPLACED ON THE STRUCTURE. CONTRACTOR SHALL SUPPORTADJACENT STRUCTURES, UTILITIES AND EXCAVATIONS AS REQUIREDCONTRACTOR SHALL SUBMIT SHOP DRAWINGS FOR ALL TEMPORARYFORMWORK, SHEETING, SHORING AND UNDERPINNING SEALEDBY A PROFESSIONAL ENGINEER AS A PART OF THE CONTRACTOR'SWORK.E. THE CONTRACTOR SHALL BE RESPONSIBLE TO DETERMINE ALLOWABLECONSTRUCTION LOADS AND TO PROVIDE DESIGN AND CONSTRUCTION OFFALSEWORK, FORMWORK, STAGINGS, BRACING, SHEETING, SHORING ANDUNDERPINNING AS NECESSARY TO PREVENT ANY LATERAL OR VERTICALMOVEMENTS TO, AND TO INSURE THE STRUCTURAL INTEGRITY OF EXISTINGBUILDINGS, STREETS, AND ANY UTILITY LINES, BRACING, SHEETING,SHORING, ETC., REQUIRED TO INSURE THE STRUCTURAL INTEGRITY OFTHE EXISTIN